1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
|
######################################################################
# LOCAL CONFIGURATION #
# Specifies settings specific for the current host #
######################################################################
# Specify your host's canonical name here. This should normally be the fully
# qualified "official" name of your host. If this option is not set, the
# uname() function is called to obtain the name. In many cases this does
# the right thing and you need not set anything explicitly.
primary_hostname =
# The next three settings create two lists of domains and one list of hosts.
# These lists are referred to later in this configuration using the syntax
# +local_domains, +relay_to_domains, and +relay_from_hosts, respectively. They
# are all colon-separated lists:
domainlist local_domains = @
domainlist relay_to_domains =
hostlist relay_from_hosts = localhost
hostlist trusted_relay_hosts_ip =
hostlist trusted_relay_hosts =
# (We rely upon hostname resolution working for localhost, because the default
# uncommented configuration needs to work in IPv4-only environments.)
# Most straightforward access control requirements can be obtained by
# appropriate settings of the above options. In more complicated situations,
# you may need to modify the Access Control Lists (ACLs) which appear later in
# this file.
# The first setting specifies your local domains, for example:
#
# domainlist local_domains = my.first.domain : my.second.domain
#
# You can use "@" to mean "the name of the local host", as in the default
# setting above. This is the name that is specified by primary_hostname,
# as specified above (or defaulted). If you do not want to do any local
# deliveries, remove the "@" from the setting above. If you want to accept mail
# addressed to your host's literal IP address, for example, mail addressed to
# "user@[192.168.23.44]", you can add "@[]" as an item in the local domains
# list. You also need to uncomment "allow_domain_literals" below. This is not
# recommended for today's Internet.
# The second setting specifies domains for which your host is an incoming relay.
# If you are not doing any relaying, you should leave the list empty. However,
# if your host is an MX backup or gateway of some kind for some domains, you
# must set relay_to_domains to match those domains. For example:
#
# domainlist relay_to_domains = *.myco.com : my.friend.org
#
# This will allow any host to relay through your host to those domains.
# See the section of the manual entitled "Control of relaying" for more
# information.
# The third setting specifies hosts that can use your host as an outgoing relay
# to any other host on the Internet. Such a setting commonly refers to a
# complete local network as well as the localhost. For example:
#
# hostlist relay_from_hosts = <; 127.0.0.1 ; ::1 ; 192.168.0.0/16
#
# The "/16" is a bit mask (CIDR notation), not a number of hosts. Note that you
# have to include 127.0.0.1 if you want to allow processes on your host to send
# SMTP mail by using the loopback address. A number of MUAs use this method of
# sending mail. Often, connections are made to "localhost", which might be ::1
# on IPv6-enabled hosts. Do not forget CIDR for your IPv6 networks.
# All three of these lists may contain many different kinds of item, including
# wildcarded names, regular expressions, and file lookups. See the reference
# manual for details.
|